⌘K
HomeRecalls 26V384000
NHTSA campaign 26V384000 · manufacturer recall MAB-3330

2024–2026 Altec AC Series Crane: equipment recall

Missing welds can lead to platform joint failure due to fatigue or overload, resulting in the platform falling from the boom tip, increasing the risk of injury.

moderate 14 vehicles affected

What was reported

Source: manufacturer filing, 49 CFR Part 573
Problem Altec Industries (Altec) is recalling certain 2024-2026 AC Series Crane vehicles. The inside joints between the side plates and the base plates of the 26-foot insulating personnel jib (IJ26) may be missing welds. Risk Missing welds can lead to platform joint failure due to fatigue or overload, resulting in the platform falling from the boom tip, increasing the risk of injury. Fix Altec will advise owners to inspect the IJ26 jib for missing welds. If the welds are missing, the jib should be taken out of service immediately. Altec will add the missing welds or provide a repair procedure and kit, free of charge. Owner notification letters were mailed July 23, 2026. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is MAB-3330.

Reported to NHTSA Jun 11, 2026 by Altec Industries, Inc, owners notified Jul 23, 2026.

Which vehicles are covered

Source: NHTSA campaign 26V384000
Model yearOn WhichTrim
2024 Altec AC Series Crane
2025 Altec AC Series Crane
2026 Altec AC Series Crane

None of the vehicles this campaign names has a page on WhichTrim: the catalogue covers the cars, trucks and SUVs the EPA certifies from 2016 on, and these vehicles fall outside it — older model years, or motorhomes, trailers, buses, motorcycles and chassis cabs the EPA does not rate. The campaign record above is complete as filed, and whether one specific vehicle is included is settled by its VIN. Other campaigns on vehicles without a page here →

The federal paperwork

Source: nhtsa.gov

Filed documents

  • Defect report PDF — The manufacturer's own filing to NHTSA describing the defect, the risk and the affected build range.

Check one specific vehicle

A recall applies to a build range, so year, make and model cannot settle it. NHTSA checks a VIN against the manufacturer's own list and tells you whether the repair is still outstanding on that vehicle.

NHTSA VIN recall lookup →

Campaign 26V384000 · the manufacturer calls it MAB-3330

Own one, or run a fleet? Recall Watch checks each VIN against every new NHTSA campaign and emails you when one lands, this one's expansions included. Or take a free one-line alert by model year.

Advertisement

Common questions

Source: NHTSA, 49 CFR Part 573

Is MAB-3330 the same recall as 26V384000?

Yes. MAB-3330 is the number Altec Industries, Inc uses for this campaign in its own paperwork and in the letter it sends owners. 26V384000 is the number NHTSA files it under. One recall, two references — dealers and service departments generally quote the manufacturer's.

Does this recall repair cost anything?

No. Federal law requires the manufacturer to remedy a safety defect or a compliance failure at no charge, for vehicles up to 15 years old measured from the date of first sale. A dealer that asks you to pay for a recall repair is in the wrong.

How do I know whether my vehicle is included?

By VIN, not by model year. The manufacturer files a build range with NHTSA and only vehicles inside it are covered, so two identical-looking cars from the same year can differ. NHTSA's own lookup checks a VIN against the manufacturer's list.

What if the repair is not available yet?

It happens, and often. Manufacturers must notify owners when a defect is found even if the parts or the software are not ready, then notify them a second time once the remedy exists. The remedy filed for this campaign is described above.

What did the manufacturer say was wrong?

The problem, risk and fix quoted on this page are the manufacturer's own words as filed with NHTSA under 49 CFR Part 573. WhichTrim does not paraphrase them.

Who started this recall?

NHTSA's record credits the manufacturer. A recall can begin with the manufacturer's own testing, with a defect investigation, or with a compliance test against a Federal Motor Vehicle Safety Standard.