Ford, Lincoln and 1 others engineering analysis EA18002
Extended Braking Distance. NHTSA’s Office of Defects Investigation opened this engineering analysis about the control unit/module on 9 model years (2007–2009). Opened Apr 18, 2018, closed Jan 15, 2021 after 2.7 years. It led to safety recall 19V904000. became a recall
What NHTSA says
Source: Office of Defects Investigation, as filedOn April 18, 2018, the Office of Defects Investigation (ODI) opened Engineering Analysis (EA) 18-002 to investigate reports of braking concerns in model year (MY) 2006-12 Ford Fusion and Lincoln MKZ, and MY 2006-11 Mercury Milan vehicles manufactured with Continental Automotive System?s ABS hydraulic control units (HCUs). Complainants report that after an ABS braking event (initiated by slippery or uneven surfaces) the brake pedal moved towards the floor and the vehicle stopping distance increased beyond driver expectations. Inside the HCU are four hydraulic normally closed (NC) valves with zinc-coated moving armatures that control the flow of brake fluid. Unstable brake fluid can degrade over time, allow the brake fluid to gel, and corrosion to form on the armatures. The high-viscosity gelation and corrosion can cause the armatures to become stuck (open). In some cases, braking returns to normal when the armature(s) subsequently become unstuck. The intermittent condition proves difficult to diagnose with complainants reporting having (non-HCU) repairs conducted only to have the condition return. During the investigation, 14 HCUs from complaint vehicles were recovered, including seven from reported crashes. NHTSA?s Vehicle Research and Test Center (VRTC) disassembled the HCUs, removed the four NC valves in each, and confirmed 22 of the 56 NC valves contained stuck armatures. On seven of the 14 HCUs, both front wheel armatures were stuck, on nine of the 14 HCUs two or three armatures were stuck. And 52 of the 56 NC armatures exhibited corrosion of the zinc coating. Forces required to extract stuck armatures from the valve sleeve were measured to range from 1.1 to 18.0 lbs. VRTC also conducted ABS braking tests on a variety of test surfaces that showed HCU failures cause increases in pedal travel and braking distances. Testing also showed that if the driver was able to apply four times the brake pedal force and two times the brake pedal travel, then high-vehicle decelerations could be achieved, however, single or multiple wheel lockups were also occurring. Based on Ford?s response to ODI?s July 20, 2018 information request letter, and complainants' reports to NHTSA, ODI identified a population of vehicles with an elevated level of field failure compared to vehicles produced both before and after. Further evaluation of Ford?s response identified that the brake fluid used to produce these vehicles, a specific formulation of a DOT3 fluid provided by CCI Corporation between February 2006 and July 2009, differed from the brake fluid used in other vehicle populations. ODI used the correlation of fluid specification and elevated field failures to identify a vehicle population exhibiting a defect trend. The complaints, crashes and injuries cited above, and the 14 recovered HCUs involve vehicles from this population. On December 18, 2019, Ford submitted safety recall (19V-904) to remedy HCU failures on the MY 2006-2010 Ford Fusion, Lincoln MKZ, and Mercury Milan vehicles manufactured with the suspect CCI brake fluid formulation. Ford will function test the HCU and replace the DOT 3 brake fluid with an improved DOT 4 brake fluid. If the HCU fails the function test, Ford will install an HCU with a different armature coating (black oxide). HCUs with black oxide coating were fully phased into Ford?s new vehicle production by MY 2016; these HCUs do not appear to be experiencing armature corrosion. ODI notes that the non-recalled EA18-002 subject vehicles, which were manufactured with a different specification brake fluid, did not display an elevated level of field failures like the recalled vehicles. Based on available information, Ford?s rec
A Engineering Analysis is the deeper stage, usually upgraded from a Preliminary Evaluation: NHTSA tests, requests engineering documents and decides whether a safety defect exists. The summary is the agency’s own text from its investigation file, unedited; the opening and closing resumes with the full reasoning are on NHTSA’s site under this number.
What this means for an owner
Source: and what happens nextAn investigation is not a finding that a defect exists, and it puts no duty on anyone. NHTSA opens a Preliminary Evaluation when complaints and other reports suggest a condition worth asking the manufacturer about; it upgrades to an Engineering Analysis when the answers warrant testing; it closes either when it recommends a recall, when the manufacturer recalls on its own, or when no defect trend is found. The agency’s own goals are about four months for a petition, eight for a Preliminary Evaluation or a Recall Query and eighteen for an Engineering Analysis; many run longer.
This one became a recall. The campaign page carries the manufacturer’s filed defect, risk and remedy, the build window and every model year covered; whether one specific vehicle is included is settled by VIN at nhtsa.gov/recalls.
Model years it names
Source: as NHTSA filed themAlso named: 2007 Ford Fusion; 2008 Ford Fusion; 2009 Ford Fusion; 2007 Lincoln MKZ; 2008 Lincoln MKZ; 2009 Lincoln MKZ; 2007 Mercury Milan; 2008 Mercury Milan; 2009 Mercury Milan.
A vehicle page’s investigation list carries the same action; a name here is the scope NHTSA opened, not a list of affected VINs.
Common questions
Source: NHTSA Office of Defects InvestigationIs EA18002 a recall?
No — it is the investigation that led to one. Recall 19V904000 is the campaign; its page carries the remedy.
Is EA18002 still open?
No. It closed on Jan 15, 2021 and led to recall 19V904000.
Which vehicles does EA18002 cover?
NHTSA opened it on 9 model years: 2007 Ford Fusion, 2008 Ford Fusion, 2009 Ford Fusion, 2007 Lincoln MKZ, 2008 Lincoln MKZ, 2009 Lincoln MKZ and more. That is the scope of the inquiry, not a list of affected vehicles; a recall, if one follows, defines its own population by VIN.