smart bulletin LI82.10-P-078896
smart filed this with NHTSA as a service bulletin dated Apr 28, 2025, received May 2, 2025, about the exterior lighting. It names 4 model years (2016–2019). A service bulletin is not a safety recall: it is the manufacturer telling its dealers how to diagnose or repair a condition, and whether the work is paid for depends on the warranty in force. Quoting the number at a service desk can save a diagnosis.
What the bulletin says
Source: NHTSA's summary of the manufacturer's communicationComplaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing.
Document filed under this number
| Document | Kind | Dated | NHTSA id | At NHTSA |
|---|---|---|---|---|
| LI82.10-P-078896 | Service bulletin | Apr 28, 2025 | 11017500 | not yet checked |
The summary is NHTSA’s abstract of the document, as filed under 49 CFR 579.5. One communication is usually filed as several documents — the bulletin, a dealer notice, an owner letter — and the number on any of them finds this page. A PDF link is shown only once NHTSA’s own server has been seen to serve that document; the rest are checked over the following nights. Quote the number at a service desk; it is what the dealer’s system is keyed on.
Model years it names
Source: as the manufacturer filed themA vehicle page’s bulletin list shows the newest few communications filed against that model year; the count there is every one.
Common questions
Source: NHTSA, 49 CFR 579.5Is smart LI82.10-P-078896 a recall?
No. A service bulletin is a manufacturer communication filed with NHTSA under 49 CFR 579.5; a safety recall carries an NHTSA campaign number (two digits, a letter, six digits) and a federal duty to repair for free. Check the vehicle’s recalls by VIN at nhtsa.gov/recalls, or on its page here.
Is the LI82.10-P-078896 repair free?
Not automatically. A service bulletin describes how to diagnose or repair a condition; who pays depends on the warranty in force, any extension, and the dealer. Quoting the number can save a diagnosis either way.
Which vehicles does LI82.10-P-078896 cover?
The manufacturer filed it against 4 model years: 2019 smart fortwo, 2018 smart fortwo, 2017 smart fortwo, 2016 smart fortwo. Whether one particular vehicle is affected is a matter of its VIN and its build, not its model year alone.